Explainer
How jet engines work: turbojets, turbofans and turboprops
A jet engine is a gas turbine: it draws in air, compresses it, burns fuel in it, and uses the hot gas to spin a turbine and push exhaust out the back.[1][2] Thrust comes from accelerating that gas rearward.[3] The four types are the turbojet, turboprop, turbofan and turboshaft.[4] Turbofans send extra air around the core, which adds thrust and cuts fuel use and noise.[5]
This explainer covers aircraft gas turbine engines in general terms, drawing on NASA’s Beginner’s Guide to Aeronautics and the FAA’s Pilot’s Handbook of Aeronautical Knowledge. Engine models and makers are not compared here.
From wartime invention to airliner standard
The gas turbine, or jet, engine was developed independently in Germany and England during World War II.[6] Today most high-speed passenger and military aircraft are powered by gas turbines.[7] Unlike a rocket, a turbine engine takes its oxygen from the surrounding air, so it cannot work in space. Most of the mass of its exhaust is air drawn from the atmosphere.[8]
Suck, squeeze, bang, blow
Air enters the front of the engine and is squeezed by a compressor. Fuel is sprayed in and burned. The hot, expanding gas spins a turbine, which turns the compressor through a shaft, and then rushes out of the back. Pushing that gas backward pushes the airplane forward.[1][2][3]
An aircraft turbine engine consists of an air inlet, compressor, combustion chambers, a turbine section and exhaust, and it produces thrust by increasing the velocity of the air flowing through it.[1] The expanding gases drive a turbine that is connected by a shaft to the compressor, which sustains the engine’s operation, while the accelerated exhaust provides thrust.[2] Thrust depends on the mass of gas accelerated and on the change in its velocity through the engine.[3] Compressors come in centrifugal-flow, axial-flow and combined centrifugal-axial designs.[9]
Four kinds of turbine engine
The FAA lists four types of aircraft turbine engine: turbojet, turboprop, turbofan and turboshaft.[4]
- Turbojet. The FAA handbook says turbojets are limited in range and endurance and respond slowly to the throttle at low compressor speeds.[10]
- Turbofan. A turbofan diverts a secondary airflow around the combustion chamber. The bypass air adds thrust, cools the engine and reduces exhaust noise, giving turbojet-like cruise speeds with lower fuel consumption.[5] Its bypass ratio is the mass airflow through the fan divided by the mass airflow through the core.[11]
- Turboprop. The turbine drives a propeller through a reduction gear. The FAA handbook says turboprops are most efficient at 250 to 400 mph and 18,000 to 30,000 feet.[12]
- Turboshaft. The engine delivers power to a shaft that drives something other than a propeller. Many helicopters use turboshafts, and they also serve as auxiliary power units on large aircraft.[13]
NASA illustrates the range with four aircraft: the DC-8 airliner with four high-bypass turbofans, the F-14 fighter with two afterburning low-bypass turbofans, the C-130 transport with four turboprops and the T-38 trainer with two turbojets.[14]
Limits and hazards
Heat is the main constraint. The highest temperature in a turbine engine occurs at the turbine inlet, so turbine inlet temperature is usually the limiting factor in operation.[15] Air density matters too: turbine thrust varies directly with density, so it falls as the air gets thinner.[16]
Debris drawn into the inlet causes foreign object damage, which includes bird strikes and ice ingestion and can destroy an engine.[17] Compressor blades are small airfoils governed by the same aerodynamics as a wing, and compressor stall is one of the operational hazards common to all turbine engines.[18] A flameout is when the fire in the engine unintentionally goes out.[19] How wings themselves stall is explained in how airplanes fly.
Instruments and computer control
Pilots monitor turbofan and turbojet power with engine pressure ratio (EPR), the ratio of turbine discharge pressure to compressor inlet pressure.[20] A full authority digital engine control (FADEC) is a digital computer system that controls the engine; it was first used in turbine-powered aircraft. Because a FADEC failure could cause a complete loss of thrust, it uses two separate, identical digital channels for redundancy.[21] How the FAA approves new designs is described in how aircraft are certified.
Read next
Next in the crash course
How turbulence is forecast, and why it injures people on planes
What causes turbulence, how forecasters predict it with SIGMETs, AIRMETs and the GTG model, who gets hurt, and why the NTSB says better data sharing matters.
More in Aviation
Questions readers ask
How does a jet engine produce thrust?
It accelerates a mass of gas toward the rear of the engine, and the thrust acts in the opposite direction. The amount of thrust depends on how much gas is accelerated and how much its speed changes.[3]
What are the main parts of a jet engine?
An air inlet, a compressor, combustion chambers, a turbine section and an exhaust. The turbine is connected by a shaft to the compressor and keeps it turning.[1][2]
What is the difference between a turbojet and a turbofan?
A turbofan diverts a secondary airflow around the combustion chamber; that bypass air adds thrust, cools the engine and reduces noise, giving similar cruise speed with lower fuel consumption.[5][2]
What does bypass ratio mean?
It is the mass of air passing through the fan divided by the mass of air passing through the engine core.[11]
Why can't jet engines work in space?
A turbine engine takes its oxygen from the surrounding air, unlike a rocket, which carries its own. With no air there is nothing to burn the fuel with.[8]
What engines do helicopters use?
Many helicopters use turboshaft engines, which deliver power to a shaft rather than producing thrust directly. Turboshafts are also used as auxiliary power units on large aircraft.[13]
Sources
· 21 claims from 2 publishers
Each numbered claim is a statement we checked against the sources listed with it. Tap a number in the text to see its sources in place.
- [1]
An aircraft turbine engine consists of an air inlet, compressor, combustion chambers, a turbine section and exhaust, and produces thrust by increasing the velocity of the air flowing through it. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbine Engines (retrieved 2026-11-07)
- [2]
In a turbojet, compressed air is mixed with fuel and ignited; the expanding gases drive a turbine connected by a shaft to the compressor, which keeps the engine running, and the accelerated exhaust provides thrust. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbojet (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbojet (retrieved 2026-11-07)
- [3]
An engine produces thrust by accelerating gas rearward, and the thrust acts in the opposite direction; its size depends on how much gas is accelerated and how much its velocity changes. confirmedas of 2026-11-07
- What is Thrust? · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- What is Thrust? · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- [4]
The four types of aircraft turbine engine are the turbojet, turboprop, turbofan and turboshaft. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Types of Turbine Engines (retrieved 2026-11-07)
- [5]
A turbofan creates additional thrust by diverting a secondary airflow around the combustion chamber; the bypass air adds thrust, cools the engine and reduces exhaust noise, giving turbojet-like cruise speed with lower fuel consumption. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbofan (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbofan (retrieved 2026-11-07)
- [6]
The gas turbine, or jet, engine was developed independently in Germany and England during World War II. confirmedas of 2026-11-07
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- [7]
Most modern high-speed passenger and military aircraft are powered by gas turbine engines. confirmedas of 2026-11-07
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- [8]
Unlike a rocket, a turbine engine takes its oxygen from the surrounding air, so it cannot work in space; most of the mass of its exhaust comes from the atmosphere. confirmedas of 2026-11-07
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- [9]
Turbine engines are classified by compressor type into centrifugal-flow, axial-flow and centrifugal-axial-flow designs. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Types of Turbine Engines (retrieved 2026-11-07)
- [10]
The FAA handbook says turbojet engines are limited in range and endurance and are slow to respond to the throttle at low compressor speeds. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbojet (retrieved 2026-11-07)
- [11]
A turbofan's bypass ratio is the mass airflow through the fan divided by the mass airflow through the engine core. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbofan (retrieved 2026-11-07)
- [12]
A turboprop is a turbine engine that drives a propeller through a reduction gear; the FAA handbook says turboprops are most efficient at 250 to 400 mph and 18,000 to 30,000 feet. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turboprop (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turboprop (retrieved 2026-11-07)
- [13]
A turboshaft delivers power to a shaft that drives something other than a propeller; many helicopters use turboshafts, and they are widely used as auxiliary power units on large aircraft. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turboshaft (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turboshaft (retrieved 2026-11-07)
- [14]
NASA gives examples of each engine type in service - the DC-8 with four high-bypass turbofans, the F-14 with two afterburning low-bypass turbofans, the C-130 with four turboprops and the T-38 with two turbojets. confirmedas of 2026-11-07
- Gas Turbine Engines · NASA Glenn Research Center · Primary source (retrieved 2026-11-07)
- [15]
The highest temperature in a turbine engine occurs at the turbine inlet, so turbine inlet temperature is usually the limiting factor in operation. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Engine Temperature Limitations (retrieved 2026-11-07)
- [16]
Turbine engine thrust varies directly with air density, so thrust falls as air density falls. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Thrust Variations (retrieved 2026-11-07)
- [17]
Debris drawn into a turbine engine causes foreign object damage, which includes bird strikes and ice ingestion and can destroy an engine. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Foreign Object Damage (FOD) (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Foreign Object Damage (FOD) (retrieved 2026-11-07)
- [18]
Compressor blades are small airfoils subject to the same aerodynamics as any airfoil, and compressor stall is one of the operational considerations common to all turbine engines. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Compressor Stalls (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Turbine Engine Operational Considerations (retrieved 2026-11-07)
- [19]
A flameout is when the fire in a gas turbine engine unintentionally goes out. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Flameout (retrieved 2026-11-07)
- [20]
Engine pressure ratio (EPR), the ratio of turbine discharge pressure to compressor inlet pressure, is used to indicate the power output of turbojet and turbofan engines. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Engine Pressure Ratio (EPR) (retrieved 2026-11-07)
- [21]
A full authority digital engine control (FADEC) is a digital computer system that controls an aircraft's engine, first used in turbine-powered aircraft; because a FADEC failure could cause a complete loss of engine thrust, it uses two separate, identical digital channels for redundancy. confirmedas of 2026-11-07
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Full Authority Digital Engine Control (FADEC) (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Full Authority Digital Engine Control (FADEC) (retrieved 2026-11-07)
- Pilot's Handbook of Aeronautical Knowledge (FAA-H-8083-25C), Chapter 7: Aircraft Systems · Federal Aviation Administration · Primary source · Full Authority Digital Engine Control (FADEC) (retrieved 2026-11-07)
Revision history (1)
- Page created.
Created Nov 7, 2026. Last reviewed by an editor on Nov 8, 2026. Next scheduled review: Nov 7, 2027.
Cite this page
"How jet engines work: turbojets, turbofans and turboprops." ContentLora, updated Nov 7, 2026. https://contentlora.com/explain/how-jet-engines-work
Spotted an error? Suggest a correction or emailcorrections@contentlora.com.