Explainer
How Wi-Fi works: 802.11, the 6 GHz band and Wi-Fi 7
Wi-Fi is built on the IEEE 802.11 standards for wireless local networks, and the Wi-Fi Alliance certifies products in numbered generations.[1][2] Wi-Fi 7, introduced in 2024, works across the 2.4, 5 and 6 GHz bands and adds 320 MHz channels in the 6 GHz band and multi-link operation; on the standards side, the IEEE's 802.11be "Extremely High Throughput" amendment targets a maximum throughput of at least 30 Gbit/s.[2][3] In the US the 6 GHz band was opened to Wi-Fi by FCC rules published in 2020, and the Wi-Fi Alliance, citing ABI Research, puts Wi-Fi devices in use in 2026 at 12.8 billion.[4][5]
This explainer covers how Wi-Fi standards and radio bands work. It does not test or recommend routers, and speed figures are the maximums stated in standards or by the Wi-Fi Alliance, not measured speeds.
Standards and generations
Wi-Fi is a wireless local network: it links your devices to a router by radio. The rules for how devices talk over the air come from the IEEE’s 802.11 standards.[1] The industry’s Wi-Fi Alliance uses simpler generation names: Wi-Fi 4, 5, 6 and 7.[6][2]
IEEE 802.11 specifies the medium access control (MAC) and physical (PHY) layers for wireless LANs.[1] New capabilities arrive as amendments: 802.11be, “Enhancements for Extremely High Throughput”, was approved by the IEEE board on 26 September 2024.[3]
According to the Wi-Fi Alliance, Wi-Fi 4 was introduced in 2009, Wi-Fi 5 in 2014, Wi-Fi 6 in 2018 and Wi-Fi 7 in 2024.[6][7][2] There is also Wi-Fi HaLow, introduced in 2017, which uses spectrum below 1 GHz to reach about 1 km for low-power sensors and wearables.[8]
Radio bands
Most Wi-Fi 5 products are dual-band, and the Wi-Fi Alliance says devices can use the less crowded 5 GHz band for demanding applications and 2.4 GHz for basic needs such as browsing and smart-home devices.[6] It says Wi-Fi 6 also brought Wi-Fi to the 6 GHz band.[7]
In the United States, rules from the FCC published in May 2020 opened the whole 6 GHz band (5.925-7.125 GHz) to unlicensed indoor low-power access points. Higher-power “standard” access points may use parts of the band under an automated frequency coordination (AFC) system that protects existing fixed microwave links, and the rules allow channels up to 320 MHz wide.[4]
How Wi-Fi 6 shares the air
The Wi-Fi Alliance says Wi-Fi 6 introduced OFDMA, which shares channels among several devices at once to raise efficiency and lower latency, along with multi-user MIMO, 160 MHz channels and target wake time, which it says improves device battery life.[7]
What Wi-Fi 7 changed
On the standards side, the IEEE’s 802.11be amendment requires at least one mode capable of a maximum throughput of at least 30 Gbit/s at carrier frequencies between 1 and 7.25 GHz, while staying compatible with older 802.11 devices in the 2.4, 5 and 6 GHz bands.[3] The Wi-Fi Alliance lists Wi-Fi 7’s main features as 320 MHz channels in the 6 GHz band, which it says double throughput compared with Wi-Fi 6; multi-link operation, which balances traffic across several links; and 4K QAM, which it says gives 20% higher transmission rates than Wi-Fi 6’s 1024 QAM.[2] The 30 Gbit/s figure is a maximum measured at the MAC layer, not a typical speed.[3]
Wi-Fi 8 and the market
The Wi-Fi Alliance presents Wi-Fi 8 as the next generation, focused on reliability and on letting access points coordinate rather than compete for spectrum. Separately, the IEEE project P802.11bn, “Enhancements for Ultra High Reliability”, aims for modes that improve on 802.11be’s Extremely High Throughput operation by 25% in throughput at one or more signal levels, in 95th-percentile latency and in lost data units.[9]
Citing ABI Research, the Wi-Fi Alliance puts 2026 Wi-Fi device shipments at 3.8 billion, devices in use at 12.8 billion and Wi-Fi 7 chipset shipments at 1.4 billion. These are an industry body’s figures from an analyst firm.[5] For the connection that reaches the router, see fibre broadband, 5G and satellite internet.
Read next
Next in the crash course
How 5G works: spectrum, standalone networks and 3GPP releases
How 5G mobile networks work: low, mid and millimetre-wave spectrum, standalone vs non-standalone, 3GPP releases, 5G-Advanced and global coverage.
Questions readers ask
What is the difference between Wi-Fi and 802.11?
IEEE 802.11 is the family of technical standards for wireless local networks, covering the medium access control and physical layers. Wi-Fi 6 and Wi-Fi 7 are generation names used by the Wi-Fi Alliance, an industry group.[1][2][7]
What does Wi-Fi 7 add?
The Wi-Fi Alliance says Wi-Fi 7 adds 320 MHz channels in the 6 GHz band, multi-link operation to spread traffic across links, and 4K QAM, which it says raises transmission rates by 20% over Wi-Fi 6's 1024 QAM.[2]
What is the top speed in the newest IEEE standard?
The IEEE 802.11be (Extremely High Throughput) amendment requires at least one mode capable of a maximum throughput of at least 30 Gbit/s, measured at the MAC layer, so it is a ceiling rather than a typical speed.[3]
Why does the 6 GHz band matter?
It adds a large block of spectrum. In 2020 the FCC opened the whole 5.925-7.125 GHz band in the US to indoor low-power Wi-Fi access points and allowed channels up to 320 MHz wide.[4]
Should I use 2.4 GHz or 5 GHz?
The Wi-Fi Alliance says dual-band networks let devices use the less crowded 5 GHz band for demanding applications and the 2.4 GHz band for basic needs such as web browsing and smart-home devices.[6]
What is Wi-Fi 8?
Wi-Fi 8 is the next generation, which the Wi-Fi Alliance says focuses on reliability and on access points coordinating instead of competing for spectrum. A separate IEEE project, P802.11bn (Ultra High Reliability), aims for 25% improvements over 802.11be in areas such as latency.[9]
Sources
· 9 claims from 3 publishers
Each numbered claim is a statement we checked against the sources listed with it. Tap a number in the text to see its sources in place.
- [1]
Wi-Fi is based on the IEEE 802.11 family of standards, which specify the medium access control (MAC) and physical (PHY) layers for wireless local area networks. confirmedas of 2026-11-07
- IEEE 802.11-2020 · IEEE Standards Association · Primary source (retrieved 2026-11-07)
- [2]
The Wi-Fi Alliance introduced Wi-Fi 7 certification in 2024; it says Wi-Fi 7 works across the 2.4, 5 and 6 GHz bands and adds 320 MHz channels in the 6 GHz band (twice the throughput of Wi-Fi 6), multi-link operation that spreads traffic across links, and 4K QAM, which it says gives 20% higher transmission rates than Wi-Fi 6's 1024 QAM. confirmedas of 2026-11-07
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- [3]
IEEE 802.11be, the "Enhancements for Extremely High Throughput" amendment to the 802.11 standard, defines at least one mode supporting a maximum throughput of at least 30 Gbit/s at carrier frequencies between 1 and 7.25 GHz, with backward compatibility with older 802.11 devices in the 2.4, 5 and 6 GHz bands; the IEEE board approved it on 26 September 2024. confirmedas of 2024-09-26
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source (retrieved 2026-11-07)
- [4]
In rules published in May 2020, the FCC opened the whole 6 GHz band (5.925-7.125 GHz) in the US to unlicensed indoor low-power access points, allowed higher-power standard access points in parts of the band under an automated frequency coordination (AFC) system that protects fixed microwave links, and enabled channels up to 320 MHz wide. confirmedas of 2020-05-26
- Unlicensed Use of the 6 GHz Band (final rule) · Federal Register (FCC) · Primary source · 2020-05-26 · Summary (retrieved 2026-11-07)
- Unlicensed Use of the 6 GHz Band (final rule) · Federal Register (FCC) · Primary source · 2020-05-26 · Summary (retrieved 2026-11-07)
- Unlicensed Use of the 6 GHz Band (final rule) · Federal Register (FCC) · Primary source · 2020-05-26 · Rule text, definitions (retrieved 2026-11-07)
- Unlicensed Use of the 6 GHz Band (final rule) · Federal Register (FCC) · Primary source · 2020-05-26 · Paragraph 2 (retrieved 2026-11-07)
- [5]
Citing ABI Research, the Wi-Fi Alliance puts 2026 Wi-Fi device shipments at 3.8 billion, Wi-Fi devices in use at 12.8 billion and Wi-Fi 7 chipset shipments at 1.4 billion. reportedas of 2026-11-07
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source · Wi-Fi by the numbers (ABI Research, 2026) (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- [6]
According to the Wi-Fi Alliance, Wi-Fi 4 was introduced in 2009 and Wi-Fi 5 in 2014; most Wi-Fi 5 products are dual-band, using the less crowded 5 GHz band for demanding uses and 2.4 GHz for basic needs. confirmedas of 2026-11-07
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- [7]
The Wi-Fi Alliance says Wi-Fi 6, introduced in 2018, added OFDMA, which shares channels among devices to raise efficiency and lower latency, multi-user MIMO, 160 MHz channels and target wake time for longer battery life, and that Wi-Fi 6 also brought Wi-Fi to the 6 GHz band. confirmedas of 2026-11-07
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 6 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- [8]
Wi-Fi HaLow, introduced in 2017, uses spectrum below 1 GHz to reach roughly 1 km for low-power sensors and wearables. confirmedas of 2026-11-07
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- [9]
The Wi-Fi Alliance presents Wi-Fi 8 as the next generation, focused on reliability and on letting access points coordinate rather than compete for spectrum; separately, the IEEE project P802.11bn, "Enhancements for Ultra High Reliability", aims for modes that improve on 802.11be's Extremely High Throughput operation by 25% in throughput at one or more signal-to-interference levels, in 95th-percentile latency and in lost data units. confirmedas of 2026-11-07
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- Wi-Fi CERTIFIED 7 · Wi-Fi Alliance · Primary source (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source · Related project P802.11bn (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source · Related project P802.11bn (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source · Related project P802.11bn (retrieved 2026-11-07)
- IEEE 802.11be-2024 · IEEE Standards Association · Primary source · Related project P802.11bn (retrieved 2026-11-07)
Revision history (1)
- Page created.
Created Nov 7, 2026. Last reviewed by an editor on Nov 8, 2026. Next scheduled review: May 1, 2027.
Cite this page
"How Wi-Fi works: 802.11, the 6 GHz band and Wi-Fi 7." ContentLora, updated Nov 7, 2026. https://contentlora.com/explain/how-wi-fi-works
Spotted an error? Suggest a correction or emailcorrections@contentlora.com.